Eagle Crusher 1200-25CC
السعر من دون ضريبة القيمة المضافة
السعر عند توقيع الطلب




طباعة
المعلومات
مجموعة المنتجات
جراشات
الماركة/الطراز
Eagle Crusher 1200-25CC
سنة الصنع
2023
ساعات الاستخدام
200 ساعة
موقع الماكينة
Hurricane، Utah
البلد
الولايات المتحدة الأمريكية
Mascus ID
3F397EEB
تفاصيل
رقم المخزون الداخلي
NC000959
رقم التصنيع
32052
نوع الكسارة
كسارة صدمية
معلومات أخرى
Receiving Hopper:
Heavy-duty, steel reinforcement of side plates, 7' 3" x 17' 10" top opening.
Vibrating Grizzly Feeder:
45-1/2" x 18’ lg., includes bolt in upper and lower grizzly decks of nominal 1-1/2” opening (or size specified per your application), 25 HP, 1200 RPM, TEFC, electric motor drive, mounted as integral part with hopper on common base.
Transition Hood:
Consisting of a heavy-duty fabricated feed chute with chain designed to accommodate vibratory type feeding mechanisms and spray bar for dust suppression.
Horizontal Shaft Impactor:
Eagle UltraMax 25 Primary/Secondary, Wt. 33,300 lbs., 34" x 48" feed opening, exclusive fixed bar solid steel sculptured rotor, cast primary curtain, secondary curtain with wear resistant replaceable liners, hydraulic shim adjustment on secondary
curtain, crusher housing split with hydraulic opening for access to rotor, curtains and replaceable liners. Blowbar removal tool included for removing and flipping blowbars;
Spring Bridge:
Primary curtain spring bridge assembly where each spring exerts a compressive force for additional stabilization of primary curtain and still allows to swing away under extreme loads, such as uncrushables, with hydraulic adjustment.
Fines Bypass Chute:
For diverting material to the under-crusher gathering hopper.
Undercrusher Gathering Hopper:
Heavy-duty steel plate complete with full length rubber flashing and replaceable liners.
Discharge Conveyor:
For conveying the crusher discharge material to the front of plant. Includes belt protecting gathering hopper with 400 Brinell replaceable liners, 42" x 32'6” formed plate type conveyor, impact absorbing slider bed with laminated impact rails at loading area, 20 troughing idlers, skirtboards with rubber flashing, 15 HP, 1800 RPM, TEFC, electric motor drive.
Platforms and Railings:
Structural steel frame with expanded metal floor, platforms and railings located at the crusher, diesel, and hopper for operation.
Main Trailer Frame:
24" wide flange beam side rails, air ride tri-axle suspension with 77.5" track axles, twelve 255/70R 22.5 tires, air-controlled brakes with emergency and service gladhands, fifth wheel plate and kingpin, prewired running lights with stop, directional and
3 light marker bar.
Hydraulic Lift/Leveling:
Set of six “stiff-leg” hydraulic cylinders controlled by an independent powered hydraulic unit complete with in-line load controls on each cylinder and directional control valves.
Drive Guards:
Formed sheet metal with wire mesh, complete with hinge type doors for easy access to pulleys and belts
Central Control Panel:
NEMA 4 type box complete with all motor controls for unit, 400 HP Square D Soft Start (or equivalent) with main breaker to provide power to motor, emergency stop pushbuttons, two #2 & #3 starters with quick disconnect plugs for radial stackers,
and one dual 115-volt plug. Remote operator’s pendant with feeder stop and emergency stop pushbuttons. Customer is responsible for supplying electric power to Panel and any special wiring as
specified by local code.
Electric Power:
250 HP, 1800 RPM, TEFC, electric motor drive.
Electric Variable Speed Feeder Control:
25 HP, adjustable frequency AC drive with remote variable speed switch; includes auxiliary circuit with starter installed in the central control panel for continuous fixed-speed operation.
Remote Feeder Start and Stop:
Remote control for starting and stopping feeder
Options Included:
Magnetic Separator:
Dings Model 44CR (or equivalent) continuous belt magnet with stainless steel discharge belt, magnet stand, chute, 5 HP, 1800 RPM, TEFC, electric motor drive, and magnet rectifier that converts AC voltage to DC voltage
Grizzly Cross Conveyor:
For discharging grizzly bypass material to side of plant, full length skirtboards with rubber flashing, 20° troughing idlers, 4 HP, motorized head pulley, special pant-leg chute with flop gate replaces standard bypass chute
¾” AR Hopper Linerعرض المزيد
تفاصيل البائع
ICM Solutions
4055 S 500 W 84123 Murray Utah الولايات المتحدة الأمريكية
الحصول على إشعار عبر البريد الإلكتروني