Masaba 48 in. Truck Unloader
السعر من دون ضريبة القيمة المضافة
9
المفضلة
حصة
حفظ عملية البحث
طباعة
المعلومات
مجموعة المنتجات
أخرى
الماركة/الطراز
Masaba 48 in. Truck Unloader
سنة الصنع
2023
ساعات الاستخدام
78 ساعة
موقع الماكينة
Boise، Idaho
البلد
الولايات المتحدة الأمريكية
Mascus ID
A48D6509
السعر
اختيار عملة
تفاصيل
رقم المخزون الداخلي
NC000971
رقم التصنيع
2023385
معلومات أخرى
2023 MASABA 48” LOW PROFILE TRUCK UNLOADER – LPTU48
LOAD AREA
• Self-Relieving Load Area
• Grate - Constructed of Heavy Duty flat bar, 10’ x 5’ outside dimension
• Ramp System - Located on each side of the Loading area.
o Includes (2) Self-Cleaning Ramps - Hinged on each side of grate, hydraulically folding for cleaning after each loading and travel
o Includes (2) Center ramps
• Masaba Patented Self-Deploying Center Ramps with Manual Folding Outer Ramps –
Center Ramps Self-Deploy with linkage system without the need of additional equipment
to lift or move it into position. Inner ramps can be disconnected for cycled cleaning.
Extended Outer 3rd Ramp – (2) 8’ extended ramps each side to grade, pins to center ramp
for operation and travel, manual folding flip out via hinge
CHASSIS
• Frame - Constructed of Heavy Duty steel tubing
• Tandem Axle - Tandem walking beam with (8) 11x22.5R tires
• Landing Jacks - hydraulic landing legs
• Road Portable Package - Including 5th wheel hitch, brakes, lights and mud flaps
48” DISCHARGE CONVEYOR (approx. 48” x 46’)
• Undercarriage - Hydraulic raise and lower, 11’ maximum discharge height
• Frame - Channel frame
• Drive – Dual Class II head drive with V-Belts and Guard
• Gear Reducers – (2) Dodge shaft mount reducers with sheaves, bushings, and backstops
• Motors - (2) WEG 25hp 1800rpm
• Capacity - 1,000 STPH of 100 PCF material, 1.5” minus spherical lumps
• Belt Speed - 225 FPM
• Flow Control – manual adjustable slide gate
• Steel Hold Down Wheels
• Loading Area Idlers – PPI, CEMA C, 5” diameter flat carrier idlers
• Transition Idlers – PPI, CEMA C, 20 degree, sealed, 5” diameter trough idlers
• Troughing Idlers – PPI, CEMA C, 35 degree, sealed, 5” diameter trough idlers
• Return Idlers – PPI, CEMA C, sealed, 5” diameter rubber disc return idlers
• Drive Pulley – PPI Heavy Duty, 20” diameter, drum pulley with 1/2" herringbone lagging
• Tail Pulley – PPI Heavy Duty, 14” diameter, self-cleaning wing pulley
• Snub Pulley – PPI Heavy Duty, 14” diameter, drum pulley with 3/8” smooth rubber lagging
• Shafts - C1045 turned and polished
• Bearings – Dodge Pillow block bearings
• Take Ups - Screw type
• Belting - 3-ply 3/16 x 1/16 330 PIW
• Belt Splice – Vulcanized Splice
• Belt Scraper – Flexco EZP1
• Discharge Hood - with 5/16” AR countersunk bolt in liners, to feed 36” belt width or greater
GENERAL SPECIFICATIONS
• Hydraulic Unit - 20hp electric pumping unit to electrically control ramps and conveyor discharge raise and lower, including continuous cycling and hot climate protection, 24V solenoids
• 13hp Electric start Gas Powered Unit – to manually operate hydraulic landing legs, conveyor raise/lower, and hinged ramp raise/lower, independently, to remove from truck and setup.
• Electrical – 480V/3ph/60Hz enclosed panel. Includes main disconnect, circuit breaker and push button on/off switches with soft start. Mounted to chassis. With 100’ lead cord
• Wireless Remote Control System
• Guarding - Appropriate guarding supplied. We do not warrant that our guards will meet all local codes. It is the responsibility of the end user to have them checked by a local inspector
• Steel Shot Blasted
• Primer - (1) coat of 2 part urethane primer
• Paint - (1) coat of 2 part urethane paint
• Owner’s Manual - (1) copy in English included for operation, maintenance, and parts
Located in our Boise, ID yardعرض المزيد
ICM Solutions
4055 S 500 W 84123 Murray Utah الولايات المتحدة الأمريكية
الحصول على إشعار عبر البريد الإلكتروني
الإبلاغ عن إعلان مريب